Exit from an inverted low wing aeroplane.
Moderators: John Dean, Moderator
-
- Posts: 87
- Joined: Wed Jan 02, 2008 11:32 pm
- Location: West Wales
Exit from an inverted low wing aeroplane.
Re: Neil Spooner ending up inverted in his Nipper. Many low wing aeroplanes have an upward opening canopy, which will prevent exit if inverted. Just how difficult is it to smash a lexan or perspex canopy if you need to get out of a crashed aircraft rapidly? Oh and what sort of implement/tool do you need to carry to do the smashing? Anyone have experience of this.
-
- Posts: 294
- Joined: Wed Jan 02, 2008 11:00 am
- Location: Bristol'ish
Yes. Without something sharp and heavy, Perspex is harder to break than you would think. Suggest a small Axe. Perspex canopies will break easily with an axe but the broken edges are then razor sharp so to get out you need to break away all the perspex trapped in the frame or get cut open crawling out. Forget "life hammers" designed for toughened glass. They are useless on perspex.
Lexan!! forget it.
My 2p
Steve
Lexan!! forget it.
My 2p
Steve
-
- Posts: 147
- Joined: Mon Jan 07, 2008 6:08 pm
- Location: EAST SUSSEX UK
- Contact:
Hi Mike, thankfully most aircraft that turn turtle will brake the canopy in the process, the problem will be if there is no roll bar or a high back to support the airframe to give you enough space to crawl out.
In the senario of an engine failure, remeber your drills and turn the fuel off and the electrics before impact, this will lessen the likelyhood of fire, and fly a controlled crash if all else fails. Post impact fires are rare, but can happen.
Will.
In the senario of an engine failure, remeber your drills and turn the fuel off and the electrics before impact, this will lessen the likelyhood of fire, and fly a controlled crash if all else fails. Post impact fires are rare, but can happen.
Will.
-
- Posts: 87
- Joined: Wed Jan 02, 2008 11:32 pm
- Location: West Wales
-
- Posts: 257
- Joined: Wed Jan 02, 2008 11:00 am
-
- Posts: 294
- Joined: Wed Jan 02, 2008 11:00 am
- Location: Bristol'ish
As Welshman says canopy acrylic is easy to crack when working but I've noticed how little the cracks migrate when it does.
In the current cold weather it might shatter better I guess.
Digging and plying with a big knife might do it if you have plenty of
time. You would need to protect your hands or get cut to ribbons.
This is what we carry now:
Another advantage of an axe is that if egress via the canopy is not possible you can hack your way out through the side of the aircraft.
Re Will's point, our canopy was indeed broken on impact with the ground.
But it was unbroken where we needed to crawl out.
Hope this persuades people to get axes.
Steve
In the current cold weather it might shatter better I guess.
Digging and plying with a big knife might do it if you have plenty of
time. You would need to protect your hands or get cut to ribbons.
This is what we carry now:
Another advantage of an axe is that if egress via the canopy is not possible you can hack your way out through the side of the aircraft.
Re Will's point, our canopy was indeed broken on impact with the ground.
But it was unbroken where we needed to crawl out.
Hope this persuades people to get axes.
Steve
Upside down, hanging in your straps and probably in a confined space does not seem to be conducive to axe swinging.
Perhaps a battery pwred hammer drill ?
When it happened to me the canopy broke and I had to dig my way out (good reason for maintiaining a slim profile) so perhaps a broad axe could double as a spade.
Perhaps a battery pwred hammer drill ?
When it happened to me the canopy broke and I had to dig my way out (good reason for maintiaining a slim profile) so perhaps a broad axe could double as a spade.
roger breckell